First week of EV driving

The first week of EV driving has been great.  Put on 220 miles this week.  So far we haven't had to use the gas motor backup (as a generator) at all.

  One day we drove the car to a local charging station to try it out.  Drove there just to try it.   So it wasn't useful other than our education.  It was only a 4 mile drive to the charge station from our house and it took about 30min to charge the car to full.  While interesting it showed me that our plan of charging exclusively at the house is the way to go. 





 
When we purchased the car the guessometer said it could go 25miles.  Which was fine for what we needed.  This morning it is up to 36 miles of expected battery range.  And after driving 14 miles to work it guesses I have 29 miles left.  That'd be 43 total miles.  Good deal.








 
When we bought the car the blower fan didn't work.  The owner stated that it probably needed a blower module replaced.  Part number 22745409.  That part number has been replaced by 22813323.  At this time 22813323 is "out of stock with no ETA on availability" at GM.  Grrr.  I did mange to find the old part number for sale and bought it.  Sure enough it fixed it.  Who hoo.  Blower works again.

Still loving the EV life :-)

Comments

Post a Comment

Popular posts from this blog

Removing the volts front seats.

Image
Our Volt didn't come with heated seats.  For what we paid for the car we were willing to over look it.  But it doesn't mean we didn't want them.  We decided to add some after market seat heaters. To remove the seat from the car:  The seat belt needs to be disconnected from the seat.  to do that pry out the little circle on the plastic bit that connects the belt to the seat.  See the picture below.  Note how the cap stays attached at the bottom. Remove the bolt in the center remove the plastic half. Then simply remove the metal tab that the belt attaches.  Might need to slide it down slightly to get it out. You may also might want to remove the head rest.  It will give more clearance for removing the seat.  Raise the headrest then remove the plastic bezels at the base of the posts by rotating them counter clockwise. To remove the headrest from the seat there is a latch on both posts that must be released.  It is a spring wire wit
Read more

Blower module

Image
Blower module aka Blower resistor replacement for a 2011 Volt (Gen1)  22745409   First step is to remove the trim on the passenger door sill.  This is required as the right outboard screw holding the lower trim panel on is not accessible with the trim on.  Removal is simply prying it up and then back.  It just has tabs that click into the slots you can see here. The next step is to remove the lower trim panel. There are three screws.  (9/32 socket fits the head) One to the right of this picture.  One to the left.  Then one to the back center (toward the front of the car).  I'll try to circle these in yellow later.  The one in the middle was missing on my car.  Makes me think someone has been here before.   Once the lower trim panel is removed there is an air duct that needs to be removed.  This was missing on my car.  Apparently the person that was in here last time didn't put it back.  Ugh.  Anyone with an extra duct le
Read more

Zilla and Warp9 (Sold):

Image
Plans change again. My son crashed his E46 (gas powered).  He bent the frame beyond repair.    Due to scheduling and things we really needed an extra car.  My plan was to buy a inexpensive overheated E46 and drop his engine in.  We shopped for a couple days but then I looked at my EV in the driveway.  It looked almost identical to the car he crashed.  So.... Yes you guessed it.  We pulled out the EV stuff and tossed in his motor and trans.  Had him up and running pretty quickly.  Long story short my EV parts are forsale . Sold http://www.diyelectriccar.com/forums/showthread.php?t=176130 If someone wanted to come to the house and pick it up  I'd toss in some other EV bits I have.
Read more