Wiring

I'm hoping by end of christmas break at the latest to have the EV moving on it's own power even if on ony 7 batts. Progress so far.

Most of the high voltage lines are done. I need to make 3 more. Still haven't finished the return lines on the PS so that's left and then wire up the Hair ball. See how much longer that takes.

Here are a few more part#'s and stores I bought from.
Contactor:
Kilovac EV200 Contactor. Purchased from E-bay

Crimping tool: Lengo Swedg-on Tool Model 840 From E-bay

Fuses and Heat shrink: purchased from EV Source LLC www.evsource.com
1ft Length, 1in Normal Adhesive Lined Heat Shrink Tubing, Red
Item# 600-HSA-001-RE-N 3ft

1ft Length, 1in Normal Adhesive Lined Heat Shrink Tubing, Black
Item# 600-HSA-001-BL-N 3ft

500A 300VDC fuse, Up to 1000A Controller up to 276V Nominal System Voltage
Item# 201-A30QS500-4 qty 2

Comments

Post a Comment

Popular posts from this blog

Removing the volts front seats.

Image
Our Volt didn't come with heated seats.  For what we paid for the car we were willing to over look it.  But it doesn't mean we didn't want them.  We decided to add some after market seat heaters. To remove the seat from the car:  The seat belt needs to be disconnected from the seat.  to do that pry out the little circle on the plastic bit that connects the belt to the seat.  See the picture below.  Note how the cap stays attached at the bottom. Remove the bolt in the center remove the plastic half. Then simply remove the metal tab that the belt attaches.  Might need to slide it down slightly to get it out. You may also might want to remove the head rest.  It will give more clearance for removing the seat.  Raise the headrest then remove the plastic bezels at the base of the posts by rotating them counter clockwise. To remove the headrest from the seat there is a latch on both posts that must be released.  It is a spring wire wit
Read more

Blower module

Image
Blower module aka Blower resistor replacement for a 2011 Volt (Gen1)  22745409   First step is to remove the trim on the passenger door sill.  This is required as the right outboard screw holding the lower trim panel on is not accessible with the trim on.  Removal is simply prying it up and then back.  It just has tabs that click into the slots you can see here. The next step is to remove the lower trim panel. There are three screws.  (9/32 socket fits the head) One to the right of this picture.  One to the left.  Then one to the back center (toward the front of the car).  I'll try to circle these in yellow later.  The one in the middle was missing on my car.  Makes me think someone has been here before.   Once the lower trim panel is removed there is an air duct that needs to be removed.  This was missing on my car.  Apparently the person that was in here last time didn't put it back.  Ugh.  Anyone with an extra duct le
Read more

1 Month with the Chevy Volt

Image
Today has been about month since we brought home the 2011 Volt.  We have put over 400 miles on it.  Only using the range extender once for about 7 miles.  The one time we used the range extender we were finally able to see how far the car would actually go on a charge.  Not just the predicted mileage. Keep in mind we live in the Appalachian mountains.  The roads are very up and down and never straight.  And on this run there were many sections of 55 MPH and we drove in sport mode (We always drive in sport mode).   And well it included a foot to the floor acceleration run from a stop light to 55 mph.  I'm sure that hurt the range.  We weren't seeing how far we could stretch the range.  We were just driving it like we would drive a car.  Anyway we got 42.3 miles on battery power alone.  Which seems right in the neighborhood of what was predicted for the car when it was new.  For a 7 year old car with a 125K miles I'm thinking that is really good.  Will a 7 year old Nissan
Read more