Posts

Trans is damaged

Image
EV construction has been slowed for some Tramission issues. I've gotten the transmission apart. The trans that "worked fine just needed a rebuild" is missing many teeth on 2nd gear. This trans is basically beyond repair. I wish it had been 1st gear as I probaby don't need 1st gear. The way it was the trans sounded like it was crunching gravel. No suprize there. For now I'm thinking I'll grind off ALL the 2nd gear teeth and just go without a 2nd gear. May not need it so much. I can get another transmission later. We'll see. I think finish my adapter plate and then decide.
Image
UPDATE: When I spun the trans with the motor the transmission sounded like it was full of rocks. I was told it made a "rattle" when I bought it. I figured it just needed new bearings but this was a much more than a rattlle. Either way the trans needed to come apart so apart it came. Turns out there are many teeth broken off 2nd gear. Too bad it wasn't first gear as it that doesn't seem to be needed in and EV. I'll spend some more time practicing rebuilding this transmission as with a car of this age the next trans I buy will likely need some rebuilding too.

Mate motor to trans

Image
Did a little more work. Mated the trans to the motor. Have some more trimming to do on the adapter plate (or plates depending on how you look at it). I mounted one plate to the motor and one to the trans. With the trans setting on the motor and the input shaft engaged with the clutch I spun the motor and centered or checked to ensure it was centered prior to pining the 2 plates together. One thing I found was the clutch alignment tool would align the clutch disc so the trans could be installed but it was not truely centered. So I used the dial indicator to center the clutch plate prior to putting on the pressure plate. This turned out perfectly. Couple of pictures. The taper lock installed on the motor Transmission on top of the motor.

More on the motor flywheel adapter.

Image
For this project I found some software to download for FREE (Alibre Design) that is ALMOST as good as what I used at work back then. Edit. Alibre Design sucks. They said it was free but then a few months later disallowed usage of the program. SO now my documents are drawn in a program I can't use. I DO NOT recommend it. As far as the wild machining. All the center features were as purchased (it started life as a taper lock sprocket). The blind tapped holes aren't too difficult. Well being the holiday I had some time to work on things. Turned down the OD of my pilot bushing myself. Seems they don't make a 15mm ID bearing with the OD to fit the Warp 9 motor. So I started with a Mcmaster carr HPF bushing (6659k28) and reduced the outside to about .001 over the bore dia of the hole in the motor. Well I first tired .010 over but when I pressed the bushing in it shrank the ID. The bushing was only a $1.50 so I had bought 2. good thing. Try 2 was successful and I now hav

Parts back from the machinist.

Image
My Flywheel adapter and one AL plate came back from the machinist today. I love seeing the parts turn from Cad into Real life. The adapter looks like it will work out exactly as planned. I have bolted it to the flywheel and slid it onto the motor shaft. I'll check it to see if it turned out true and straight and then I can go on to making the transmission plate. Here ae a couple pics. Below is the adapter setting in the back of the flywheel
Image
Here's and update. Holidays and my online racing season have been keeping me busy. But above is a picture of the the taper lock sprocket and taperlock bushing I purchased to use in my flywheel adapter (finally got around to ordering). Also pictured is an aluminum plate I'll use for part of the motor spacer, a bronze bushing I'll use as the pilot bushing (have to alter the OD slightly) and some keystock. Dropped the Taperlock off at the machinist today. Should be a week or so until I get that back. I'm anxious to bolt the flywheel to the motor.

Purchase Chassis "donor car"

Image
I picked up a chassis for the swap and at the same time got a ride in Ben's ("TelnetManta's") EV saturday. Here's a pic of me pulling the BMW home with the land rover. Incidently I had just rebuilt the land rover's auto trans myself. After that experience I really have no interest of an auto trans in my EV....Or any other car for that matter.